1.14-inch 80x160 tft display
1.14-inch tft display with a resolution of 80×160, IPS display mode, SPI 4 lane interface, suitable for application scenarios requiring space
Main parameters of 1.14inch tft display
| ITEM | Standard value | UNIT |
| LCD SIZE | 1.14 | INCH |
| LCD Type | TFT Negative Transmissive | — |
| Driver Element | a-Si TFT Active matrix | — |
| Number of Dots | 80*(RGB)*160 | Dots |
| Pixel Arrangement | RGB Vertical Stripe | — |
| Pixel Pitch (W*H) | 0.219*0.219 | mm |
| Active Area | 14.864*24.912 | mm |
| Viewing Direction | all view direction | — |
| Control IC | ST7789 | — |
| Module Size(W*H*T) | 14.864(W)*31.0(L)*1.6(H) | mm |
| Back Light | White LED | |
Download relevant technical documents
ST7789 data sheet for small lcd display
Specification of 1.14-inch small lcd display
initial code for 1.14-inch small lcd display
Customize the length, width and thickness of FPC or cable, adjust the pin arrangement according to the interface type, and select the appropriate connector. Make your display or circuit board simple and safe with an excellent FPC solution.
A touch screen can be added according to your requirements, there are three options: resistive touch screen, capacitive touch screen, infrared touch screen. Or add protective glass as needed
Display screens with different optical parameters can be designed according to needs, such as brightness, color gamut, response time, gamma and other parameters, and anti-glare, anti-fingerprint coatings, etc. can also be added
The circuit board we designed can convert the interface of your display into an HDMI interface. If your product does not have any display control capabilities, you can use our serial display and only need to use simple commands to control the displayed content through RS232/458
1.14-inch tft display drawings and interfaces
1.14-inch TFT display with 80×160 resolution and IPS display mode, which can provide excellent viewing angles and contrast. If you need a matching touch screen, we can also customize it. The 1.14-inch bar type LCD supports optical bonding to achieve a more suitable touch screen fit.
The 1.14-inch bar type LCD has a slender appearance, active area: 14.86×24.91, LCD display module size: 14.86x31x1.6, suitable for small equipment.
The driver IC ST7789 supports SPI, MCU, and RGB interfaces and can be easily driven. The backlight has 1 LED light, operating voltage: 3V, operating current: 20mA, module brightness 400cd/㎡, the product complies with Rohs standards, the FPC and your motherboard are connected by welding, if you need to change to ZIF or BTB, please contact us .
The outline drawing is as follows:
Interfaces are defined as follows：
| Pin | Symbol | Detail |
| 1 | NC | |
| 2 | NC | |
| 3 | SDA | SPI interface input/output pin.the data is latched on the rising edge of the SCL signal. |
| 4 | SCL | This pin is used to be serial interface clock |
| 5 | RS | Display data/command selection pin in 4-line serial interface. |
| 6 | RES | This signal will reset the device and it must be applied to properly initialize the chip.Signal is active low. |
| 7 | CS | Chip selection pin;Low enable,high disable. |
| 8 | GND | |
| 9 | NC | |
| 10 | VCC | Power Supply for Logic |
| 11 | LEDK | backlight unit power supply |
| 12 | LEDA | backlight unit power supply |
| 13 | GND |
1.14 -inch 80x160 tft display application cases
The 1.14-inch LCD is suitable for e-cigarettes due to its slim ratio. Compared to OLeds, LCDS offer faster refresh rates, richer colors and longer life, all of which can make your products better
UPS is short for uninterruptible power supply. It is used in data centers, home storage systems, and offices to provide power for a short time in case of power failure, ensuring data stability. UPS products only need to display simple content such as the capacity of the battery and the time it can be used. Low-resolution OLED is more suitable.
