0.66-inch 64x48 PMOLED Display Module
0.66 64×48 PMOLED Display Module, Display Mode: Passive Matrix, Display Color: Monochrome (White)
Main parameters of 0.66-inch PMOLED Display Module
| ITEM | Standard value | UNIT |
| Display SIZE | 0.66 | INCH |
| Display Type | PMOLED | — |
| Driver Element | Passive Matrix | — |
| Number of Dots | 64*48 | Dots |
| Display Color | Monochrome (White） | — |
| Pixel Pitch (W*H) | 0.19*0.19 | mm |
| Active Area | 13.42*10.06 (mm) | mm |
| Viewing Direction | all direction | — |
| Control IC | SSD1306 | — |
| Panel Size(W*H*T) | 18.46(W)*18.1(L)*1.25(H) | mm |
Download relevant technical documents
SSD1306 data sheet for small oled display
Specification of 0.66-inch small oled display
initial code for 0.66-inch small oled display
Circuit diagram of 0.66-inch small oled display
Customize the length, width and thickness of FPC or cable, adjust the pin arrangement according to the interface type, and select the appropriate connector. Make your display or circuit board simple and safe with an excellent FPC solution.
A touch screen can be added according to your requirements, there are three options: resistive touch screen, capacitive touch screen, infrared touch screen. Or add protective glass as needed
Display screens with different optical parameters can be designed according to needs, such as brightness, color gamut, response time, gamma and other parameters, and anti-glare, anti-fingerprint coatings, etc. can also be added
The circuit board we designed can convert the interface of your display into an HDMI interface. If your product does not have any display control capabilities, you can use our serial display and only need to use simple commands to control the displayed content through RS232/458
0.66-inch OLED Display drawings and interfaces
The 0.66-inch monochrome OLED display module has a compact diagonal size of 0.66 inches and consists of 64×48 individual white OLED pixels. The driver IC is SSD1306, which supports 8080 4-bit/8-bit parallel and I2C/4-wire serial interfaces. With the controller chip’s integrated voltage generation, the display requires only a single 3.3V supply, simplifying overall system design. Since the OLED is self-illuminating, it has a viewing angle that exceeds that of a tft display.
The display uses a solder-type flexible printed circuit (FPC), eliminating the need for connectors. Integration is easy by simply soldering the FPC directly to the PCB. And it can be easily controlled by various microcontrollers such as 8051, PIC, AVR, ARDUINO, ARM and Raspberry Pi. This makes it suitable for a variety of applications including embedded systems, industrial equipment, security systems, medical equipment and handheld devices.
The outline drawing is as follows:
Interfaces are defined as follows：
| Pin | Symbol | detail |
| 1 | NC | |
| 2 | C2P | Positive Terminal of the Flying Inverting Capacitor Negative Terminal of the Flying Boost Capacitor |
| 3 | C2N | |
| 4 | C1P | |
| 5 | C1N | |
| 6 | VBAT | Power Supply for DC/DC Converter Circui |
| 7 | VSS | GND |
| 8 | VDD | Power Supply for Logic |
| 9 | BS1 | Communicating Protocol Select |
| 10 | BS2 | |
| 11 | CS | Chip Select |
| 12 | RES | Power Reset for Controller and Driver |
| 13 | DC | Data/Command Control |
| 14 | RW | Read/Write Select or Writ |
| 15 | E/RD | Read/Write Enable or Read |
| 16 | D0 | Host Data Input/Output Bus |
| 17 | D1 | |
| 18 | D2 | |
| 19 | D3 | |
| 20 | D4 | |
| 21 | D5 | |
| 22 | D6 | |
| 23 | D7 | |
| 24 | IREF | Current Reference for Brightness Adjustment |
| 25 | VCOMH | |
| 26 | VCC | Power Supply for OEL Panel |
| 27 | VLSS | Ground of Logic Circuit |
| 28 | NC |
